Wax car Shine and protection

The car always looked solid, it is followed properly. If the body is shiny, then any car looks more expensive. This effect can be achieved by using wax which is the most popular method of treatment of the body. Types of wax very much, but not all give good results. Will tell you what are the tools and how to use them correctly. Also note, some manufacturers have been recognized and what to pay attention to when choosing wax for a car.


What is the treatment car wax

Besides the beautiful appearance, the wax for the car body which performs a number of tasks:

  • Protects metal parts from rust.
  • Masks minor scratches.
  • Forms on the surface of the exterior film that protects the surface from moisture, small stones and other environmental factors.
  • Prolongs life of paint and varnish that cover the body.
  • Facilitates the cleaning process.

Best wax for car is one who not only looks beautiful but protects the body.

The types of car wax

On the market there are five varieties of wax for car:

  1. Spray.

    Its peculiarity is that it is very easy to apply. However, among car enthusiasts and specialists of this coating is considered the worst option: often, this wax is washed off after the first car wash.

  2. Liquid wax for car.

    The application process is more complex than in the case of the spray, but the effect of it lasts longer. Usually, the manufacturers guarantee that the coverage is enough for 4-5 washes.

  3. Solid (hard) wax. the types of wax

    Sophisticated technology application, which includes thorough polishing of the car. If the right to perform the work, the coating will stay 3-4 months.

  4. Synthetic wax.

    It is recommended to use in winter to protect from snow and cold. In the case of a competent application of the coating is maintained until 6 months.

  5. The hot wax.

    The main advantage of this tool before cold wax for car in pronounced sheen on the surface of the body. The coating has good protective properties. Service life depends on the specific composition.

How to apply wax on the car

Instructions for using wax is available on each package, and it is important to follow it point by point. The specific steps depend on the type of wax you chose. We will give only a General idea about the process.

Regardless of the choice of means, before processing a waxed car, it is necessary to prepare:

  • Thoroughly wash the surface to remove even the smallest dirt particles. If this is not done, the wax can go smoothly and very quickly slip away. For a more efficient wash, use a car shampoo.
  • Wait for complete drying of the car, if you're using hard wax, and partial drying — if the wax is liquid.
  • To put the car away from the sunlight in the room, closed against the wind.

Cover car liquid wax

how to apply wax

First we need to dissolve the wax in warm water: the temperature and the proportions must be indicated on the packaging. It is important that the temperature difference between the body and the diluted wax was not more than 20 degrees.

Coating of car wax usually takes 20 to 30 minutes. Start with the roof and slowly go down. After all the surface is treated, you need to wait 1-2 minutes and to handle the vehicle with air to remove excess moisture. Then the body first with a cloth, sponge or cloth to carefully allocate and fix the wax on the surface and remove excess.

How to cover the car hard wax

When working with a solid structure you need to follow the instructions:

  • Apply a small amount of wax on a small area.
  • Take a rag or sponge and carefully spread the wax over a wider surface.
  • Repeat first two steps until you cover with wax the entire body.
  • Wait until the medium dries. Exact drying time depends on the specific composition, and is usually indicated on the packaging. You can also define it by outward signs: arida wax gives a matte patina over the entire surface.
  • Take a microfiber cloth and complete the polishing of the body to Shine.

Before you apply the wax on the car, be sure to watch the video to have a more visual representation of the process.